Published On: August 6ᵗʰ, 2019 02:03
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Array Antenna (AIR-ANT2513P4M-N)
This document describes the AIR-ANT2513P4M-N antenna and provides electrical specifications and mounting instructions. The antenna is a four-port polarization-diverse patch array that operates over the 2.4-GHz and 5-GHz Wi-Fi bands. It ships with an articulating mount for use on flat surfaces and masts and is adjustable in both the horizontal and vertical planes. The radome is paintable using commonly available non-conductive spray paints, such as Krylon or Rust-Oleum. The antenna is designed for use in indoor and outdoor environments with Cisco Aironet 3702P and 1570 series access points.
Technical Specifications
Figure 1 ANT2513P4M-N front high view

System Requirements
This antenna is designed for use with Cisco Aironet 3702P and 1570 series access points. The antenna can be mounted on a wall, a ceiling, or a pole with a maximum diameter of 5 inches (12.7 cm).
Safety Instructions

Warning IMPORTANT SAFETY
INSTRUCTIONS
This warning symbol means danger. You are in a situation that could
cause bodily injury. Before you work on any equipment, be aware of
the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement
number provided at the end of each warning to locate its
translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS

Warning Only trained and
qualified personnel should be allowed to install, replace, or
service this equipment.
Statement 1030
Follow these safety instructions when installing your antenna.
- Plan your installation procedure carefully and completely before you begin.
- If you are installing an antenna for the first time, for your own safety as well as others, seek professional assistance. Consult your dealer, who can explain which mounting method to use for the location where you intend to install the antenna.
- Select your installation site with safety, as well as performance, in mind. Remember that electric power cables and telephone lines look alike. For your safety, assume that any line is an electric power line until determined otherwise.
- Call your local power company or building maintenance organization if you are unsure about cables close to your mounting location.
- When installing your antenna, do not use a metal ladder. Do dress properly: shoes with rubber soles and heels, rubber gloves, and a long sleeved shirt or jacket.
- If an accident or emergency occurs with the power lines, call for qualified emergency help immediately.
Installation Notes
Because antennas transmit and receive radio signals, they are susceptible to RF obstructions and common sources of interference that can reduce throughput and range of the device to which they are connected. Follow these guidelines to ensure the best possible performance:
- Mount the antenna to utilize its propagation characteristics. This antenna is designed to radiate energy in a somewhat narrow beam from the front of the antenna. It should be aimed into the intended coverage area.
- Keep the antenna away from metal obstructions such as heating and air-conditioning ducts, large ceiling trusses, building superstructures, and major power cabling runs. If necessary, use a rigid conduit to lower the antenna away from these obstructions.
- The density of the materials used in a building’s construction determines the number of walls the signal must pass through and still maintain adequate coverage. Consider the following before choosing the location to install your antenna:
– Signals penetrate paper, vinyl
and drywall the easiest. A signal can penetrate five or six walls
constructed of drywall or wood.
– Signals are more heavily
attenuated passing through concrete and solid-wood walls.
– Signals often reflect off thick
metal walls and may not penetrate at all.
Choosing a Mounting Location
The antenna should be mounted clear of any obstructions to the side or front of the enclosure. Keep in mind that this antenna should be aimed into the intended coverage area, so you should mount the antenna so that the desired mechanical tilt can be achieved. If possible, mount the antenna near the access point so you can use the shortest possible connecting cables.
Installing the Antenna
You can install the antenna on any flat surface or on a pole with a minimum diameter of 2 inches (5.08 cm) and a maximum diameter of 5 inches (12.7 cm). The antenna and one mounting flange are connected together when shipped. When mounting the antenna you need to assemble the bracket hardware, connect the antenna and bracket to the mounting surface, and adjust the antenna orientation.
Contents of Antenna Bracket Kit
Figure 4 shows the parts included with the antenna bracket.
Figure 4 Antenna Bracket Kit Contents


Note One flange (not
pictured here) ships attached to the antenna. The flange pictured
here is the one that you attach to the wall or the pole.
Tools and Equipment Required
You will need these tools to loosen and tighten the adjustment bolts on the bracket:
To mount the antenna on a wall or ceiling, you will need these supplies:

Note The fasteners and
mounting surface should be capable of maintaining a minimum pullout
force of 150 pounds (68 kg) to support the weight of the antenna
and bracket plus the potential wind loading on the antenna.
To mount the antenna on a pole or mast, you will need either or both of these supplies:

Note The pole or mast
must be rigid enough to hold the weight of the antenna plus the
associated forces produced by wind loads. In addition, the pole or
mast must be structurally strong enough to withstand the clamping
force of the hose clamps.
You may need the following tools and equipment, which are not provided:
Mounting on a Wall or Ceiling
Follow these steps to mount your antenna on a wall or ceiling.
Step 1 Remove the antenna and bracket hardware from the
shipping container.
Step 2 Determine the mounting location for the antenna.

Note The fasteners and
mounting surface should be capable of maintaining a minimum pullout
force of 150 pounds (68 kg) to support the weight of the antenna
plus the potential wind loading on the antenna.
Step 3 Attach the mounting bracket to the wall or ceiling
using four screws or bolts and anchors through the holes on the
bracket.
Figure 5 shows the wall-mount bracket.
Figure 5 Wall-Mount Bracket and Dimensions (in millimeters)

Step 4 Assemble the bracket hardware as shown in
Figure 6.
Figure 6 Assembling the Bracket Hardware

Step 5 Make sure you orient the antenna correctly (note the
arrow on the back of the antenna that indicates the top of the
antenna). Use a 1/2 in. (13-mm) wrench to loosen the elevation
adjustment bolt and the elevation pivot bolt.
Step 6 Adjust the azimuth (side-to-side position) and
elevation (up-and-down position) of the antenna. Loosen the
adjustment bolts slightly to allow for adjustment. Azimuth angle
can be adjusted ±25 degrees and elevation can be adjusted ±60
degrees. You can use the azimuth and elevation markings on the
mounting arm and the wall flange as a guide.
Step 7 After you adjust the antenna position, tighten the
adjustment bolts and the pivot bolts. Tighten all bolts to 18.7 +/-
5 lb-ft (25.4 Nm).
Step 8 Connect the antenna cables to the access point. The
antenna ports are labeled A through D, from left to right.
– On the AP3702P, connect the antenna port A to
connector A on the access point, antenna port B to connector B, and
so on.
– On the AP1570, connect antenna port A to Port 1 on
the AP, antenna port B to port 2 on the AP, and so on.
See the Suggested Cable section for cable recommendations.
Mounting on a Pole or Mast
The antenna can be mounted on a pole or mast using two hose clamps.

Note The pole or mast
must be rigid enough to hold the weight of the antenna plus the
associated forces produced by wind loads. In addition, the mast
must be structurally strong enough to withstand the clamping force
of the hose clamps.
To mount the antenna on a pole or mast, follow these steps.
Step 1 Follow steps 1 and 2 from the
Mounting on a Wall or Ceiling section.
Step 2 Position and mount the mounting flange (Figure
4) onto the pole or mast using the hose clamps provided in the
kit. The hose clamps should pass through the slots on the mounting
flange (Figure
5).
Step 3 Tighten the clamps only enough to hold the flange and
antenna in place until the antenna is positioned to its final
position.
Step 4 Assemble the antenna and bracket to the flange as
shown in
Figure 6.
Step 5 Position the antenna, mounting bracket, and hose
clamps on the mast.
Step 6 Tighten the hose clamps until the antenna is fully
secure on the mast. Ensure that the antenna cannot rotate about the
mast.
Step 7 After the antenna is secured on the mast, adjust the
azimuth and elevation.
To adjust the azimuth and elevation, use a 1/2 in. (13-mm) wrench to loosen the adjustment bolts. Azimuth can be adjusted ±25 degrees and elevation can be adjusted ±60 degrees.
Step 8 After you adjust the antenna position, tighten the
adjustment bolts. Tighten all bolts to 18.7 +/- 5 lb-ft (25.4
Nm).
Step 9 Connect the antenna cables to the access point. The
antenna ports are labeled A through D, from left to right. Connect
the antenna port A to connector A on the access point, antenna port
B to connector B on the access point, and so on. See the
Suggested Cable section for cable recommendations.
Suggested Cable
Cisco recommends a high-quality, low-loss cable for use with the antenna, such as Cisco AIR-CAB005LL-R-N= (5 ft low-loss cable with RP-TNC and N-type connectors) for AP3702P, or AIR-CAB005LL-N= or AIR-CAB010LL-N= (5 ft and 10 ft N-type connectors, respectively) for AP1570. Four cables are required.

Note Coaxial cable loses
efficiency as the frequency increases, resulting in signal loss.
The cable should be kept as short as possible because cable length
also determines the amount of signal loss (the longer the run, the
greater the loss).
Painting the Antenna
Painting the antenna and the bracket does not affect its performance if you use standard exterior-grade, oil-based or latex paint. Do not use metallic or metallic-flake paints, which will degrade antenna performance.

Note Before painting the
antenna, cover the pressure-release vent on the rear, lower-left of
the antenna with masking tape to prevent clogging (Figure
3).
Cisco recommends Krylon Fusion for Plastic or Rust-Oleum for Plastic (which might require a primer coat). For best results, follow the surface preparation suggestions from the paint manufacturer.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.