Published On: August 6ᵗʰ, 2019 02:00
Install Mode Versus Bundle Mode
Install Versus Bundle Mode
Cisco Catalyst 3850 Series Switches have two modes of operation, Install mode and Bundle mode. This document describes the two modes and how to set the mode of operation.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Restrictions for Install Mode Versus Bundle Mode
The Install mode and the Bundle mode of operation have the following restrictions:
-
Booting from a USB driver or TFTP in Install mode is not supported.
-
Booting the switch in Bundle mode consumes more memory than the Install mode because the packages are extracted from the bundle and copied to the RAM.
-
Auto-upgrade feature is disabled by default and is not available in the Bundle mode.
Information About Install Mode Versus Bundle Mode
Cisco Catalyst 3850 Series Switches have two modes of operation, Install and Bundle. Two or more switches must be in the same boot mode to form a switch stack.
The Install mode is the recommended mode for booting a switch.
Install Mode
The Install mode uses a package-provisioning file named packages.conf in order to boot a switch. In addition, there are a number of .pkg files in the flash drive. We recommend that you do not alter the packages.conf and .pkg files unless directed by a Cisco Technical Assistance Center (TAC) engineer.
Bundle Mode
The Bundle mode uses monolithic Cisco IOS images to boot a switch. The Bundle mode consumes more memory than the Install mode because the packages are extracted from the bundle and copied to RAM.
Switch Stack Membership
A standalone switch operates as the active switch . You can connect one standalone switch to another standalone switch to create a switch stack containing two stack members, with one of them acting as the active switch. You can also connect standalone switches to an existing switch stack to increase the stack membership.
Verifying and Converting the Mode of Operation
Verifying the Mode of Operation
Before You Begin
Procedure
Ensure that the TFTP server is reachable.
 Note |
The recommended size of the TFTP block size to 8192. To improve the TFTP blocksize, use the ip tftp blocksize bytes command in global configuration mode. |
Example: Verifying the Mode of Operation
The following example shows a sample output for the show version command used for verifying the mode of operation:
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253
[v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details,
see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the
IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
Device uptime is 8 minutes
Uptime for this control processor is 15 minutes
System returned to ROM by Power Failure
System image file is "flash:packages.conf"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http : //tools.cisco. com/legal /export /pepd /Search. do
If you require further assistance please contact us by sending email to export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Converting from Install Mode to Bundle Mode
Procedure
Example: Converting from Install Mode to Bundle Mode
The following example shows how to convert from Install mode to Bundle mode:
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
Device uptime is 8 minutes
Uptime for this control processor is 15 minutes
System returned to ROM by Power Failure
System image file is "flash:packages.conf"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http ://www.cisco.com /wwl /export /crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850-24T Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 INSTALL
Configuration register is 0x102
Devie# show boot
---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable does not exist
z
Boot Variables on next reload:
BOOT variable = flash:packages.conf;
Manual Boot = yes
Enable Break = no
Device# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Device(config)# no boot system
Device(config)# boot system switch all flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin
Device(config)# do write memory
Building configuration...
Compressed configuration from 9209 bytes to 4151 bytes[OK]
Device(config)# exit
Device# reload
Reload command is being issued on Active unit, this will reload the whole stack
Proceed with reload? [confirm]
Chassis 1 reloading, reason - Reload command
Nov 17 12:37:17.120 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: reload fp action requested
Nov 17 12:37:32.323 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: process exit with reload stack code
octeon_wdt: WDT device closed unexpectedly. WDT will not stop!
reboot: Restarting system
Booting...(use SKIP_POST)(use DDR clock 667 MHz)
The system is not configured to boot automatically. The
following command will finish loading the operating system
software:
boot
switch: b
Reading full image into memory
...............................................................................................one
Bundle Image
--------------------------------------
Kernel Address : 0x53430f98
Kernel Size : 0x338fbf/3379135
Initramfs Address : 0x53769f57
Initramfs Size : 0xc82830/13117488
Compression Format: mzip
Bootable image at @ ram:0x53430f98
Bootable image segment 0 address range [0x81100000, 0x81b083c0] is in range [0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin" uncompressed and installed, entry point: 0x81669190
Loading Linux kernel with entry point 0x81669190 ...
Bootloader: Done loading app on core_mask: 0xf
### Launching Linux Kernel (flags = 0x5)
pci 0001:01:00.0: of_irq_parse_pci() failed with rc=-19
mtd: bad character after partition (r)
sd 1:0:0:0: [sdb] No Caching mode page found
sd 1:0:0:0: [sdb] No Caching mode page found
sd 1:0:0:0: [sdb] No Caching mode page found
%IOSXEBOOT-4-WATCHDOG_DISABLED: (rp/0): Hardware watchdog timer disabled: disabled by BOOT_PARAM
dplr_pcie: Enabled MSI returned 0
Waiting for 120 seconds for other switches to boot
#######################################################################################################################
Switch number is 1
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
FIPS: Flash Key Check : Begin
FIPS: Flash Key Check : End, Not Found, FIPS Mode Not Enabled
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http :// www.cisco.com/wwl / export/crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
WARNING:
Executing this command will disable the password recovery mechanism.
Do not execute this command without another plan for
password recovery.
Press RETURN to get started!
Device> enable
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
NSWA uptime is 1 minute
Uptime for this control processor is 8 minutes
System returned to ROM by Power Failure
System image file is "flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http :// www.cisco.com /wwl /export/crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850-24T Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 BUNDLE
Configuration register is 0x102
Converting from Bundle Mode to Install Mode
Procedure
| Command or Action | Purpose | |
|---|---|---|
| Step 1 | enable Example: Device> enable |
Enables privileged EXEC mode. Enter your password if prompted. |
| Step 2 | show version Example: Device# show version |
Verifies the mode of operation. |
| Step 3 | show boot Example: Device# show boot |
Displays the contents of the BOOT variable, the name of the configuration file pointed to by the CONFIG_FILE variable, the contents of the BOOTLDR variable, and the configuration register setting. |
| Step 4 | request platform software package expand Example: Device# request platform software package expand |
Expands individual Cisco IOS XE software packages and the provisioning file from a specified bundle to a specific destination directory. |
| Step 5 | dir
Example: Device# dir |
Displays the list of files on a file system. |
| Step 6 | no boot system Example: Device(config)# no boot system |
Removes the startup system image specification. |
| Step 7 | boot system switch all
flash Example: Device(config)# boot system switch all flash |
Updates the boot variable on all the switches in the stack. |
| Step 8 | exit
Example: Device(config)# exit |
Exits the configuration mode to the next highest mode in the hierarchy. |
| Step 9 | write memory Example: Device# write memory |
Copies the file from the source to the destination. |
| Step 10 | show boot Example: Device# show boot |
Displays the contents of the BOOT variable, the name of the configuration file pointed to by the CONFIG_FILE variable, the contents of the BOOTLDR variable, and the configuration register setting. |
| Step 11 | reload Example: Device# reload |
Reloads the operating system. |
| Step 12 | show version Example: Device# show version |
Verifies the mode of operation. |
Example: Converting from Bundle Mode to Install Mode
The following is the sample output of the show version command that shows the conversion from Bundle mode to Install mode:
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
Device uptime is 12 minutes
Uptime for this control processor is 19 minutes
System returned to ROM by Power Failure
System image file is "flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http ://www.cisco.com /wwl /export/crypto/tool/stqrg .html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850-24T Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 BUNDLE
Configuration register is 0x102
Device# show boot
---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable = flash:packages.conf;
Boot Variables on next reload:
BOOT variable = flash:packages.conf;
Manual Boot = yes
Enable Break = no
NSWA#request platform software package expand switch 1 file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin to flash:
[1]: Expanding file
[1]: Finished expanding all-in-one software package in switch 1
SUCCESS: Finished expanding all-in-one software package.
Device# dir
Directory of flash:/
62082 -rwx 0 Oct 5 2015 10:08:32 -08:00 test.txt
62090 drwx 4096 Oct 6 2015 02:25:23 -08:00 core
62959 drwx 4096 Sep 30 2015 10:20:02 -08:00 dv
62085 -rw- 76 Nov 17 2015 11:53:08 -08:00 boothelper.log
62092 drwx 4096 Oct 29 2015 06:40:55 -08:00 virtual-instance
62278 -rw- 4868 Nov 17 2015 10:12:21 -08:00 packages.conf.00-
62084 -rw- 469326057 Nov 17 2015 11:45:23 -08:00 cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin
62492 -rw- 4875 Nov 17 2015 12:14:02 -08:00 packages.conf
62277 drwx 4096 Oct 29 2015 06:40:55 -08:00 vman_fdb
62280 drwx 4096 Oct 29 2015 06:42:23 -08:00 wnweb_store
62091 drwx 4096 Nov 17 2015 11:53:06 -08:00 dc_profile_dir
62259 -rwx 251312 Oct 7 2015 08:13:01 -08:00 netperf
108663 drwx 4096 Sep 14 2015 08:52:02 -08:00 .prst_sync
108665 drwx 4096 Feb 16 2015 18:18:47 -08:00 .rollback_timer
108666 drwx 4096 Feb 16 2015 18:18:55 -08:00 .installer
62261 drwx 4096 Oct 7 2015 08:34:56 -08:00 binaries
108674 drwx 4096 Feb 24 2015 00:35:55 -08:00 .ssh
62095 -rwx 2516 Nov 17 2015 11:53:01 -08:00 bootloader_evt_handle.log
62094 -rwx 10999 Feb 18 2015 15:53:45 -08:00 exe_list
62488 -rw- 280912575 Nov 17 2015 12:13:01 -08:00 cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg
62490 -rw- 7197312 Nov 17 2015 12:13:03 -08:00 cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg
62253 -rw- 4868 Nov 13 2015 16:32:00 -08:00 packages.conf.01-
62096 -rwx 422 Oct 5 2015 13:30:17 -08:00 recoveryhelper.log
62097 -rwx 0 Oct 5 2015 13:30:20 -08:00 tracelogs.2Wt
62098 drwx 20480 Oct 22 2015 08:54:27 -08:00 tracelogs
62087 -rwx 2097152 Nov 17 2015 12:00:40 -08:00 nvram_config
62255 -rwx 19156 Oct 7 2015 08:07:20 -08:00 polaris_merge_files.py
62256 -rwx 9318400 Oct 7 2015 08:09:08 -08:00 unixbench.tar
62257 -rwx 942080 Oct 7 2015 08:09:46 -08:00 nbench.tar
62258 -rwx 44697600 Oct 7 2015 08:12:31 -08:00 lmbench.tar
62260 -rwx 261508 Oct 7 2015 08:14:06 -08:00 netserver
62269 -rwx 77296 Oct 7 2015 08:28:33 -08:00 nbench
62270 -rwx 12838 Oct 7 2015 08:29:07 -08:00 RunDtTests.py
62271 -rwx 113 Oct 7 2015 08:30:00 -08:00 COM.DAT
62272 -rwx 3167 Oct 7 2015 08:30:25 -08:00 NNET.DAT
62276 -rw- 30412800 Oct 7 2015 09:07:35 -08:00 lmbench-x86.tar
139684 drwx 4096 Oct 19 2014 04:28:07 -08:00 lmbench
62093 -rw- 616 Nov 13 2015 15:15:05 -08:00 vlan.dat
62489 -rw- 166576756 Nov 17 2015 12:13:03 -08:00 cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg
62491 -rw- 14631548 Nov 17 2015 12:13:04 -08:00 cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg
62089 -rw- 4868 Nov 13 2015 13:26:27 -08:00 packages.conf.02-
62266 -rw- 0 Mar 17 2015 13:10:49 -08:00 .gz.TEMP_IN_PROGRESS
1749458944 bytes total (482185216 bytes free)
Device# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Device(config)# no boot system
Device(config)# boot system switch all flash:packages.conf
Device(config)# exit
Device# write memory
Building configuration...
Compressed configuration from 9150 bytes to 4070 bytes[OK]
Device# show boot
---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable = flash:packages.conf;
Boot Variables on next reload:
BOOT variable = flash:packages.conf;
Manual Boot = yes
Enable Break = no
NSWA#reload
Reload command is being issued on Active unit, this will reload the whole stack
Proceed with reload? [confirm]
Chassis 1 reloading, reason - Reload command
Nov 17 12:18:53.848 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: reload fp action requested
Nov 17 12:19:06.785 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: process exit with reload stack code
octeon_wdt: WDT device closed unexpectedly. WDT will not stop!
reboot: Restarting system
Booting...(use SKIP_POST)(use DDR clock 667 MHz)
The system is not configured to boot automatically. The
following command will finish loading the operating system
software:
boot
switch: b
Getting rest of image
Reading full image into memory...Check base package header ...: done = 16384
Getting rest of image
Reading full image into memory....done
Reading full base package into memory...: done = 280912575
Bundle Image
--------------------------------------
Kernel Address : 0x534332d0
Kernel Size : 0x338fbf/3379135
Initramfs Address : 0x5376c28f
Initramfs Size : 0xc82830/13117488
Compression Format: mzip
Bootable image at @ ram:0x534332d0
Bootable image segment 0 address range [0x81100000, 0x81b083c0] is in range [0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@boot_system: 377
Loading Linux kernel with entry point 0x81669190 ...
Bootloader: Done loading app on core_mask: 0xf
### Launching Linux Kernel (flags = 0x5)
pci 0001:01:00.0: of_irq_parse_pci() failed with rc=-19
mtd: bad character after partition (r)
sd 1:0:0:0: [sdb] No Caching mode page found
sd 1:0:0:0: [sdb] No Caching mode page found
sd 1:0:0:0: [sdb] No Caching mode page found
%IOSXEBOOT-4-WATCHDOG_DISABLED: (rp/0): Hardware watchdog timer disabled: disabled by BOOT_PARAM
dplr_pcie: Enabled MSI returned 0
Waiting for 120 seconds for other switches to boot
#######################################################################################################################
Switch number is 1
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
FIPS: Flash Key Check : Begin
FIPS: Flash Key Check : End, Not Found, FIPS Mode Not Enabled
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http ://www.cisco.com/wwl/export /crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
WARNING:
Executing this command will disable the password recovery mechanism.
Do not execute this command without another plan for
password recovery.
Press RETURN to get started!
Device> enable
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:003253 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151116_230450 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 16-Nov-15 16:34 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
NSWA uptime is 2 minutes
Uptime for this control processor is 10 minutes
System returned to ROM by Power Failure
System image file is "flash:packages.conf"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http ://www.cisco.com/wwl /export/crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
3830880K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850-24T Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 INSTALL
Configuration register is 0x102
Auto-upgrading a New Switch in a Switch Stack
Use the Auto-Upgrade feature of the Cisco Catalyst 3850 Series Switches to auto upgrade a switch to a switch stack:
Note |
The Auto-Upgrade feature is not available in the Bundle mode. |
| Command or Action | Purpose | |
|---|---|---|
| Step 1 | software auto-upgrade enable Example: Device(config)# software auto-upgrade enable |
Enables the feature for any new switches that join the stack. |
| Step 2 | end Example: Device(config)# end |
Ends the current configuration session and returns to privileged EXEC mode. |
| Step 3 | reload
switch Example: Device# reload slot 2 |
Reloads the newly added switch. |
| Step 4 | show switch
Example: Device# show switch |
Displays information related to a stack member or the switch stack. |
| Step 5 | show version Example: Device# show version |
Verifies the mode of operation. |
Example: Auto-upgrading a New Switch in a Switch Stack
The following example shows how to automatically upgrade a new switch in a switch Stack:
Note |
The slot mentioned in the following commands denotes the switch in the stack (slot 1= switch 1). |
Device# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Device(config)# software auto-upgrade enable
Device(config)# end
Device# reload slot 2
Stack is in Half ring setup; Reloading a switch might cause stack split
Proceed with reload? [confirm]
Device# show switch
Switch/Stack Mac Address : 2037.0653.0c80 - Local Mac Address
Mac persistency wait time: Indefinite
H/W Current
Switch# Role Mac Address Priority Version State
------------------------------------------------------------
*1 Active 2037.0653.0c80 1 P2 Ready
2 Standby 6c20.56bb.4980 1 V01 Ready
Device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Experimental Version Denali 16.1.20151117:183058 [v161_0_throttle-BLD-BLD_V161_0_THROTTLE_LATEST_20151117_170238 104]
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 17-Nov-15 10:32 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.1, engineering software (D)
Device uptime is 28 minutes
Uptime for this control processor is 35 minutes
System returned to ROM by Power Failure
System image file is "flash:packages.conf"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http ://www.cisco.com/wwl/export/ crypto/tool/stqrg. html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
lanbasek9 Permanent lanbasek9
cisco WS-C3850-24P (MIPS) processor with 894696K/6147K bytes of memory.
Processor board ID FOC1602V2GZ
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
147136K bytes of Crash Files at crashinfo:.
1735776K bytes of Flash at flash:.
891K bytes of TCL Script Files at script:.
7565008K bytes of USB Flash at usbflash0:.
0K bytes of at webui:.
250456K bytes of Crash Files at crashinfo-2:.
1609272K bytes of Flash at flash-2:.
3830880K bytes of USB Flash at usbflash0-2:.
Base Ethernet MAC Address : 20:37:06:53:0c:80
Motherboard Assembly Number : 73-12238-03
Motherboard Serial Number : FOC160159MG
Model Revision Number : P2
Motherboard Revision Number : 03
Model Number : WS-C3850-24P
System Serial Number : FOC1602V2GZ
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850-24T Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 INSTALL
2 32 WS-C3850-24P Denali 16.1.1 CAT3K_CAA-UNIVERSALK9 INSTALL
Switch 02
---------
Switch uptime : 11 minutes
Base Ethernet MAC Address : 6c:20:56:bb:49:80
Motherboard Assembly Number : 73-14441-03
Motherboard Serial Number : FHH1636001B
Model Revision Number : P3A
Motherboard Revision Number : 02
Model Number : WS-C3850-24P
System Serial Number : FHH1637P00U
Configuration register is 0x102
Upgrading to a New Software Version
Software Clean-Up
To install a new version of the software, clean-up the old installation files in flash drive. Perform the following step to clean up the old installation files:
Before You Begin
Procedure
Ensure that the TFTP server is reachable.
Note |
The recommended TFTP block size to 8192. To increase the TFTP block size, use the ip tftp blocksize bytes command in global configuration mode. |
Note |
Use switch all option to clean up all switches in your stack. |
| Command or Action | Purpose | |
|---|---|---|
| Step 1 | request platform software package clean switch all file
flash Example: Device# request platform software package clean switch all file flash: |
Removes the old installation files. |
Example: Software Clean-Up
Device# request platform software package clean switch all file flash: Running command on switch 1 Cleaning up unnecessary package files Scanning boot directory for packages ... done. Preparing packages list to delete ... done. Running command on switch 2 Cleaning up unnecessary package files Scanning boot directory for packages ... done. Preparing packages list to delete ... done. The following files will be deleted: [1]: /flash/cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin /flash/cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/packages.conf /flash/packages.conf.00- /flash/packages.conf.01- /flash/packages.conf.02- [2]: /flash/cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin /flash/cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg /flash/packages.conf /flash/packages.conf.00- /flash/packages.conf.01- /flash/packages.conf.02- Do you want to proceed? [y/n]y [1]: Deleting file flash:cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin ... done. Deleting file flash:cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:packages.conf ... done. Deleting file flash:packages.conf.00- ... done. Deleting file flash:packages.conf.01- ... done. Deleting file flash:packages.conf.02- ... done. SUCCESS: Files deleted. [2]: Deleting file flash:cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin ... done. Deleting file flash:cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg ... done. Deleting file flash:packages.conf ... done. Deleting file flash:packages.conf.00- ... done. Deleting file flash:packages.conf.01- ... done. Deleting file flash:packages.conf.02- ... done. SUCCESS: Files deleted.
Upgrading to a New Version of Software in Install Mode
Before You Begin
Procedure
Note |
The recommended TFTP block size to 8192. To increase the TFTP block size, use the ip tftp blocksize bytes command in global configuration mode. |
| Command or Action | Purpose | |
|---|---|---|
| Step 1 | request platform software
package install switch all file flash Example: Device# request platform software package install switch all file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin auto-copy |
Upgrades a consolidated package or an individual subpackage. |
| Step 2 | reload Example: Device# reload |
Reloads the operating system. |
Example: Upgrading to a New Version of Software in Install Mode
Device# request platform software package install switch all file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin auto-copy Expanding image file: flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin [1]: Copying flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.bin from switch 1 to switch 2 [2]: Finished copying to switch 2 [1 2]: Expanding file [1 2]: Finished expanding all-in-one software package in switch 1 2 SUCCESS: Finished expanding all-in-one software package. [1 2]: Performing install SUCCESS: install Finished [1]: install package(s) on switch 1 --- Starting list of software package changes --- Old files list: Removed cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg New files list: Added cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Finished list of software package changes SUCCESS: Software provisioned. New software will load on reboot. [1]: Finished install successful on switch 1 [2]: install package(s) on switch 2 --- Starting list of software package changes --- Old files list: Removed cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg Removed cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.pkg New files list: Added cat3k_caa-rpbase.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-srdriver.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-wcm.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Added cat3k_caa-webui.BLD_V161_0_THROTTLE_LATEST_20151116_230450.SSA.pkg Finished list of software package changes SUCCESS: Software provisioned. New software will load on reboot. [2]: Finished install successful on switch 2 Checking status of install on [1 2] [1 2]: Finished install in switch 1 2 SUCCESS: Finished install: Success on [1 2]
Upgrading to a New Version of Software in Bundle Mode
Before You Begin
Procedure
Ensure that the TFTP server is reachable.
Note |
The recommended TFTP block size to 8192. To improve the block size, use the ip tftp blocksize bytes command in global configuration mode. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
| Step 1 | request platform software
package copy switch all file flash Example: Device# request platform software package copy switch all file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.bin |
Downloads the .bin file to active storage.
Copy the .bin file to all the stack members. |
||
| Step 2 | configure terminal Example: Device# configure terminal Device(config)# |
Enters global configuration mode, when using the console port. |
||
| Step 3 | boot system flash Example: Device(config)# boot system flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.bin |
Boots the router from internal flash memory. |
||
| Step 4 | end Example: Device(config)# end Device# |
Ends the current configuration session and returns to privileged EXEC mode. |
||
| Step 5 | write memory Example: Device# write memory |
Copies the file from the source to the destination. |
Example: Migrating to a New Version of Software in Bundle Mode
The following example shows how to migrate to a new version of software in Bundle mode:
Device# request platform software package copy switch all file flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.bin [1]: Copying flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.bin from switch 1 to switch 2 [2]: Finished copying to switch 2 SUCCESS: Finished copying package(s) to the selected switch(es) Device# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Device(config)# boot system flash:cat3k_caa-universalk9.BLD_V161_0_THROTTLE_LATEST_20151024_170213.SSA.bin Device(config)# end Device# write memory Building configuration... Compressed configuration from 9354 bytes to 4241 bytes[OK]
Additional References for Install versus Bundle Mode
Related Documents
Technical Assistance
| Description | Link |
|---|---|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for Install Mode Versus Bundle Mode
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.|
Feature Name |
Releases |
Feature Information |
|---|---|---|
|
Install Mode Versus Bundle Mode |
Cisco IOS XE Release Denali 16.1.1 |
The Install Versus Bundle feature describes the two modes, Install mode and Bundle mode and how to set the mode of operation. The following commands were added or modified: request platform software package expand switch all file flash, request platform software package clean switch all file flash, request platform software package install switch all file flash, request platform software package copy switch all file flash |
Copyright © 2017, Cisco Systems, Inc. All rights reserved.