Table 1 DFC Daughter Card Specifications

Statement 1071—Warning Definition

Warning	IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS
Waarschuwing	BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES
Varoitus	TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET
Attention	IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS
Warnung	WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza	IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI
Advarsel	VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE
Aviso	INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES
¡Advertencia!	INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES
Varning!	VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR
Aviso	INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES
Advarsel	VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034

Removing the CFC Daughter Card

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To remove a CFC daughter card, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the Ethernet module from the Catalyst 6500 series switch.

If you are unsure about the correct procedure for removing a module from the switch chassis, refer to the “Removing and Installing Ethernet Modules in the Chassis” section for removal instructions.

Step 3 Place the Ethernet module on an antistatic mat with the front of the module facing toward you.

Step 4 Use a Phillips-head screwdriver to remove the installation hardware, which consists of three securing screws and the two cap nuts. (See Figure 1.)

Figure 1 CFC Daughter Card Installation Hardware

Step 5 To unseat the CFC daughter card from the Ethernet module, hold each tab at the rear of the CFC daughter card between your thumb and index finger, and gently press down on both tabs until the connectors are unseated. (See Figure 2.)

Caution Do not apply too much pressure on the tabs because you might cause damage to the module.

---

Figure 2 Unseating the CFC Daughter Card Connectors

Step 6 Gently lift the CFC daughter card with both hands and remove the CFC daughter card from the module.

Step 7 Place the CFC daughter card on an antistatic mat, antistatic foam pad, or in an antistatic bag.

Step 8 Proceed to the “Installing the DFC3B and DFC3C Daughter Cards” section.

Removing the DFC3 Daughter Card

This section contains two DFC3 daughter card removal procedures. The first procedure describes how to remove the DFC3 daughter card from modules that are not equipped with a stiffener bracket. The second procedure describes how to remove the DFC daughter card from early versions of the WS-X6748-GE-TX Ethernet module that are equipped with a stiffener bracket.

Note Only some versions of the WS-X6748-GE-TX Ethernet module are equipped with a stiffener bracket.

Removing the DFC3 Daughter Card from Modules without Stiffener Brackets

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To remove the DFC3 daughter card from modules that are not equipped with a stiffener bracket, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the Ethernet module from the chassis.

If you are unsure about the correct procedure for removing a module from the switch chassis, refer to the “Removing an Ethernet Module from the Chassis” section for removal instructions.

Step 3 Place the Ethernet module on an antistatic mat with the front of the module facing toward you.

Step 4 If your DFC daughter card has a small metal installation bracket as shown in Figure 3, use a No.1 Phillips-head screwdriver to remove the two cap nuts and the one screw securing the bracket. Set them aside with the bracket. If there is no bracket, just remove the two cap nuts and the one screw.

Step 5 Remove the remaining installation hardware. (See Figure 3.)

Note The installation hardware shown in Figure 3 is for a DFC3B or DFC3BXL daughter card. The installation hardware for a DFC3C or a DFC3CXL daughter card consists of 6 screws, 2 cap nuts, and 1 standoff.

Figure 3 Removing the DFC Daughter Card Installation Hardware

Step 6 Partially reinstall the cap nut, rotating about 3 turns so that there is a space of about 1/8 inch (3 mm) between the bottom of the cap nut and the top of the DFC3 daughter card, as shown in Figure 4. The cap nut acts as a stop when you unseat the daughter card connector so that the DFC3 daughter card does not move horizontally and cause damage to the base board.

Figure 4 Partially Installing the Cap Nut

Step 7 With your left hand, lift slightly at the location shown in Figure 5. While lifting with your left hand, rock the DFC3 daughter card up and down with your right hand, no more than half an inch in either direction, to unseat the DFC3 daughter card from the module.

Figure 5 Unseat the DFC3 Daughter Card from the Module

Step 8 Remove the one cap nut.

Step 9 Holding the DFC3 daughter card with both hands, gently lift it straight up from the module. (See Figure 6.) Immediately place the DFC3 daughter card on an antistatic mat, antistatic foam pad, or in an antistatic bag.

Figure 6 Removing the DFC3 Daughter Card from the Module

Removing the DFC3 Daughter Card from WS-X6748-GE-TX Modules Equipped with a Stiffener Bracket

Some early versions of the WS-X6748-GE-TX Ethernet modules have a stiffener bracket mounted across the top front part of the module. A modified procedure to remove the DFC daughter card from WS-X6748-GE-TX Ethernet modules equipped with a stiffener bracket is included.

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To remove a DFC3 daughter card from a WS-X6748-GE-TX Ethernet module that is equipped with a stiffener bracket, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the WS-X6748-GE-TX Ethernet module from the Catalyst 6500 series switch.

If you are unsure about the correct procedure for removing a module from the switch chassis, refer to the “Removing and Installing Ethernet Modules in the Chassis” section for removal instructions.

Step 3 Place the module on an antistatic mat or antistatic foam with the front of the module facing toward you.

Step 4 If your DFC daughter card has a small metal installation bracket as shown in Figure 7, use a No.1 Phillips-head screwdriver to remove the two cap nuts and the one screw securing the bracket. Set them aside with the bracket. If there is no installation bracket, remove the two cap nuts and the one screw.

Step 5 Use a Phillips-head screwdriver to remove the remaining installation hardware. (See Figure 7.)

Figure 7 Removing the Installation Hardware (DFC3B/DFC3BXL Shown) (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Note The two screws securing the DFC3 daughter card that pass through the front stiffener bracket tabs are longer than the remaining DFC installation screws.

Step 6 With your left hand, lift slightly at the location shown in Figure 8, and gently rock the DFC3 daughter card up and down to unseat the daughter card from the module connectors.

Figure 8 Unseating the DFC Connectors (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Step 7 Holding the DFC3 daughter card with both hands, carefully lift the back end of the DFC3 daughter card up slightly to clear the module connectors, and then carefully slide the DFC3 daughter card out from under the two front stiffener bracket tabs. Lift the DFC3 daughter card straight up from the module (see Figure 9) and immediately place the removed DFC3 daughter card on an antistatic mat, antistatic foam pad, or in an antistatic bag.

Figure 9 Removing the DFC3 Daughter Card (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Removing the Memory Module

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To remove the existing memory module from the Ethernet module, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Locate the memory module on the Ethernet module. (See Figure 10.)

Figure 10 Location of the Memory Module on a WS-X67xx Module

Step 3 Release the two spring clips on either side of the memory module to release it from the socket. (See Figure 11Figure 11.)

Figure 11 Releasing the Memory Module Spring Clips

Step 4 Grasp the edges of the memory module with your thumb and forefinger, and gently pull the memory module completely out of the socket.

Caution Memory modules are sensitive components that are susceptible to ESD damage. To prevent ESD damage, handle the memory module by the edges only; avoid touching the memory chips, pins, or traces (the metal fingers along the connector edge of the memory module). (See Figure 12.)

---

Figure 12 Handling a Memory Module

Step 5 Immediately place the old memory module in an antistatic bag to protect it from ESD damage.

Installing the 1-GB Memory Module Upgrade

Caution Memory modules have sensitive components that are susceptible to ESD damage. To prevent ESD damage, handle memory modules by the edges only; avoid touching the memory chips, pins, or traces (the metal fingers along the connector edge of the SODIMM). (See Figure 12.)

---

To install the 1-GB memory module on the Ethernet module, follow these steps:

Step 1 Verify that an ESD grounding strap is still securely attached to your wrist and to a proper earth ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the 1-GB memory module from the antistatic shipping bag.

Step 3 Hold the sides of the 1-GB memory module between your thumbs and forefingers with the component side up and with the connector edge (the metal fingers) facing away from you. (See Figure 12.)

Step 4 Tilt the 1-GB memory module to approximately the same angle as the socket, and insert the connector edge of the memory module into the socket.

Caution When inserting the memory module, use firm but not excessive pressure. If you damage a socket, you will have to return the Ethernet module to the factory for repair.

---

Step 5 Press the front edge of the 1-GB memory module down until both spring clips on the socket engage the sides of the memory module securing the memory module in place. (See Figure 13.)

Figure 13 Installing the SODIMM

Step 6 After the memory module is installed, check that both spring clips are fully engaged. If they are not, the memory module is not seated properly. If the memory module appears misaligned, carefully remove it and reseat it in the socket. Push the memory module firmly back into the socket until the spring clips snap into place.

Installing the DFC3B, DFC3BXL, DFC3C, and DFC3CXL Daughter Cards on Ethernet Modules without Stiffener Brackets

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To install the DFC daughter cards on Ethernet modules that do not have stiffener brackets, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the new DFC3 daughter card from the antistatic bag and the installation hardware from the packaging.

Note The DFC3 daughter card is designed to be installed on different modules; therefore, there may be more mounting holes on the DFC3 daughter card than there are standoffs on the module. Not all mounting holes on the DFC3 daughter card are used in all installations. Visually verify that there are standoffs beneath the mounting holes before installing the installation hardware.

Step 3 Align the mounting holes on the DFC3 daughter card (see Figure 14) with the male standoffs on the module. (See Figure 15.) Make sure that the remaining mounting holes on the DFC3 daughter card are aligned with the remaining standoffs on the module.

Figure 14 Mounting Holes on the DFC3 Daughter Card

Figure 15 Male Standoff Locations on the WS-X67 xx Modules

Step 4 Ensure that the connectors on the DFC3 are aligned with the connectors on the module. Figure 16 shows the connectors on the underside of the DFC3.

Figure 16 DFC3 Daughter Card Connectors (Underside of DFC Daughter Card Shown)

Step 5 Apply pressure to the area shown in Figure 17 to seat the power connector.

Figure 17 Seating the Power Connector

Caution Use care not to damage the connectors on the module. If you damage a connector, you will need to return the module to Cisco for repair.

---

Step 6 Position the installation bracket over the two male standoffs at the back of the DFC daughter card. Apply pressure only to the top of the bracket to fully seat the DFC3 daughter card on the module as shown in Figure 18.

Caution When seating the DFC daughter card, do not apply pressure to any other location on the DFC daughter card, especially the heat sinks. If you exert pressure on the heat sinks, they can break off of the components they are attached to.

---

Figure 18 Seating the DFC3 Daughter Card on the Module

Step 7 Use a Phillips-head screwdriver to install the installation hardware:

a. For the DCFCB and the DFC3BXL daughter cards, install the 8 screws and the 2 standoffs. (See Figure 19.)

b. For the DFC3C and the DFC3CXL daughter cards, install the 6 screws, 2 cap nuts, and the 1 standoff. (See Figure 20.)

Caution You must install all of the installation hardware. The screws provide grounding between the DFC3 daughter card and the module. Failure to install all of the screws will invalidate the safety approvals and create a risk of fire and electrical hazard.

---

Note You should visually verify that there are standoffs beneath the mounting holes before installing the installation hardware.

Figure 19 Installing the Installation Hardware (DFC3B and DFC3BXL)

Figure 20 Installing the Installation Hardware (DFC3C and DFC3CXL)

Step 8 Reinstall the Ethernet module in the chassis.

If you are unsure about the correct procedure for installing an Ethernet module in the switch chassis, refer to the “Removing and Installing Ethernet Modules in the Chassis” section for installation instructions.

Installing the DFC3B, DFC3BXL DFC3C, and DFC3CXL Daughter Cards on Ethernet Modules Equipped with a Stiffener Bracket

Some early versions of the WS-X6748-GE-TX Ethernet module have a stiffener bracket mounted across the top front part of the module. This stiffener bracket requires a modified procedure to install the DFC3 daughter card.

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

To install the DFC daughter card on an early version of the WS-X6748-GE-TX Ethernet module that is equipped with a stiffener bracket, follow these steps:

Step 1 Attach an ESD grounding strap to your wrist and to ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Remove the new DFC3 daughter card from the antistatic bag and the installation hardware from the bag.

Note The DFC3 daughter card is designed to be installed on different modules; therefore, there may be more mounting holes on the DFC3 daughter card than there are standoffs on the module. Not all mounting holes on the DFC3 daughter card are used in all installations. Visually verify that there are standoffs beneath the mounting holes before installing the installation hardware.

Step 3 Position the DFC3 daughter card over the Ethernet module, and slightly tilt the DFC3 daughter card so that the back end will clear the module connectors.

Step 4 Carefully slide the DFC3 under the two stiffener bracket tabs. (See Figure 21.) Verify that the DFC daughter card is under the two stiffener bracket tabs.

Caution You must position the DFC daughter card under the two stiffener bracket tabs. If you install the DFC daughter card above the two stiffener bracket tabs, you can permanently damage the DFC daughter card.

---

Step 5 Align the mounting holes on the DFC3 daughter card with the male standoffs on the module. (See Figure 21.) Make sure that the remaining mounting holes on the DFC3 daughter card are aligned with the remaining standoffs.

Note You should visually verify that there are standoffs beneath the mounting holes before installing the installation hardware.

Step 6 Press down on the edge of the DFC3 daughter card (see Figure 21) to seat the DFC3 daughter card power connector to the module power connector.

Figure 21 Seating the DFC Daughter Card Power Connector (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Step 7 Position the installation bracket over the two standoffs and press down only on the top of the bracket to seat the DFC3 daughter card connectors on the module connectors. (See Figure 22.)

Caution When seating the DFC3 daughter card on the module connectors, DO NOT touch or apply any pressure to the heat sinks. Press down only on the installation bracket.

---

Figure 22 Seating the DFC3 on the Module (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Step 8 Secure the DFC3 daughter card to the module through the stiffener bracket with the two long screws that you previously removed.

Step 9 Install the remainder of the screws and the cap nuts to fully attach the DFC3 daughter card to the module:

a. For the DFC3B and DFC3BXL daughter cards, install the remaining 6 screws and 2 cap nuts. (See Figure 23.)

b. For the DFC3C and DFC3CXL daughter cards, install the remaining 4 screws, 2 cap nuts, and 1 standoff. (See Figure 24.)

Caution Do not overtighten the installation hardware because you will damage the board.

---

Figure 23 Installing the DFC3B and DFC3BXL Installation Hardware (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Figure 24 Installing the DFC3C and DFC3CXL Installation Hardware (WS-X6748-GE-TX Equipped with a Front Stiffener Bracket)

Caution You must install all of the installation hardware. The screws provide grounding between the DFC3 daughter card and the module. Failure to install all of the screws invalidates the safety approvals and presents a risk of fire and electrical hazard.

---

Step 10 Reinstall the Ethernet module in the chassis.

If you are unsure about the correct procedure for installing the Ethernet module in the switch chassis, refer to the “Installing an Ethernet Module in the Chassis” section for installation instructions.

Removing an Ethernet Module from the Chassis

To remove an Ethernet module from the chassis, perform these steps:

Step 1 Disconnect any network interface cables attached to the Ethernet module.

Step 2 Attach an ESD grounding strap to your wrist and to a proper ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 3 Verify that the captive installation screws on all of the modules in the chassis are tight. This step ensures that the space created by the removed module is maintained.

Note If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on the installed modules expand and push the modules toward the open slot, which reduces the opening size and makes it difficult to reinstall the module.

Step 4 Loosen the two captive installation screws on the Ethernet module.

Step 5 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following two sets of substeps:

Horizontal slots

a. Place your thumbs on the left and right ejector levers located on the left and right sides of the module faceplate, and simultaneously rotate the levers outward to unseat the Ethernet module from the chassis backplane connector.

b. Grasp the front edge of the Ethernet module and slide the module part of the way out of the slot. Place your other hand under the Ethernet module to support the weight of the module. Do not touch the module circuitry.

c. Place the removed Ethernet module on a properly grounded antistatic mat or antistatic foam.

Vertical slots

a. Place your thumbs on the ejector levers located at the top and bottom of the Ethernet module, and simultaneously rotate the levers outward to unseat the Ethernet module from the chassis backplane connector.

b. Grasp the front edge of the Ethernet module and slide the module part of the way out of the slot. Place your other hand under the Ethernet module to support the weight of the module. Do not touch the module circuitry.

c. Place the removed Ethernet module on a properly grounded antistatic mat or antistatic foam.

Installing an Ethernet Module in the Chassis

Caution To prevent ESD damage, handle modules by the carrier edges only and wear grounding wrist straps.

---

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

To install a module in the chassis, perform these steps:

Step 1 Verify that an ESD grounding strap is attached to your wrist and to proper ground.

If you are unsure about the correct way to attach an ESD grounding strap, refer to the “Attaching Your ESD Grounding Strap” section for instructions.

Step 2 Verify that the captive installation screws are tightened on all of the modules installed in the chassis. This step assures that the EMI gaskets on all of the installed modules are fully compressed in order to maximize the opening space for the Ethernet module.

Note If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on the installed modules expand and push the modules toward the open slot, which reduces the opening size and makes it difficult to reinstall the module.

Step 3 Fully open both ejector levers on the Ethernet module. (See Figure 25.)

Step 4 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following two sets of substeps:

Horizontal slots

a. Position the Ethernet module in the slot. (See Figure 25.) Make sure that you align the edges of the module carrier with the slot guides on each side of the slot.

b. Carefully slide the Ethernet module into the slot until the EMI gasket along the top edge of the module makes contact with the module in the slot above it and both ejector levers have engaged and closed to approximately 45 degrees with respect to the Ethernet module faceplate. (See Figure 26.)

c. Using the thumb and forefinger of each hand, grasp the two ejector levers and press down to create a small (0.040 inch [1 mm]) gap between the module’s EMI gasket and the module above it. (See Figure 26.)

Caution Do not press down too hard on the levers because they can bend and be damaged.

---

d. While gently pressing down, simultaneously close the left and right ejector levers to fully seat the Ethernet module in the chassis backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 27.)

Note Failure to fully seat the module in the chassis backplane connector can result in error messages.

e. Tighten the two captive installation screws on the Ethernet module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

f. Verify that the Ethernet module STATUS LED is lit. Check the STATUS LED periodically. If the STATUS LED changes from orange to green, the module has successfully completed the boot process and is now online. If the STATUS LED remains orange or turns red, the module has not successfully completed the boot process and may have encountered an error.

Figure 25 Positioning the Module in a Horizontal Slot Chassis

Figure 26 Clearing the EMI Gasket in a Horizontal Slot Chassis

Figure 27 Ejector Lever Closure in a Horizontal Slot Chassis

Vertical slots

a. Position the Ethernet module in the slot. (See Figure 28.) Make sure that you align the edges of the module carrier with the slot guides on the top and bottom of the chassis slot.

b. Carefully slide the Ethernet module into the slot until the EMI gasket along the right edge of the module faceplate makes contact with the module in the slot adjacent to it and both ejector levers have closed to approximately 45 degrees with respect to the Ethernet module faceplate. (See Figure 29.)

c. Using the thumb and forefinger of each hand, grasp the two ejector levers and exert a slight pressure to the left, deflecting the module approximately 0.040 inches (1 mm) to create a small gap between the module’s EMI gasket and the module adjacent to it. (See Figure 29.)

Caution Do not exert too much pressure on the ejector levers because they can bend and be damaged.

---

d. While gently pressing on the ejector levers, simultaneously close them to fully seat the Ethernet module in the chassis backplane connector. The ejector levers are fully closed when they are flush with the Ethernet module faceplate. (See Figure 30.)

e. Tighten the two captive installation screws on the Ethernet module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

f. Verify that the Ethernet module STATUS LED is lit. Check the STATUS LED periodically. If the STATUS LED changes from orange to green, the module has successfully completed the boot process and is now online. If the STATUS LED remains orange or turns red, the module has not successfully completed the boot process and may have encountered an error.

Figure 28 Positioning the Module in a Vertical Slot Chassis

Figure 29 Clearing the EMI Gasket in a Vertical Slot Chassis

Figure 30 Ejector Lever Closure in a Vertical Slot Chassis

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

© 2003–2010 Cisco Systems, Inc. All rights reserved.